Installed plugs in the open ports of the pitot & static manifolds.  I installed these manifolds to allow for easy expansion in the future, to run lines to a second/third EFIS, autopilot, and whatever new gadget comes along that needs it.  I haven’t found the second long screw I bought to secure these, though…looking like a fresh one from Menard’s.

Installed the center bearing block for the rudder pedals.

Shaped the upper body of the Gretz pitot tube slightly as needed to fit into the pitot mast, put the nutplates on the mast, and installed it to the wing.  Then, installed the pitot tube to the mast after trimming the pressure line and wires as needed, and wired/plumbed it.  I decided to try using a straight quick-connect union to join the 1/4″ copper line from the pitot tube to the nylon tubing which runs through the wing, since they’re supposed to be OK for all types of tubing.  If it doesn’t work, there’s plenty of room and remaining length on the tubes to do it a different way.  With the pitot installed, I rolled the wing cart over to the fuselage and plugged the left wing in, to verify operation of the heater.  Cooling it off with a cupful of ice water caused the heater to kick on, and the indicators indicated appropriately.  Check.

Drilled attachment holes in the rudder cable fairings, then match-drilled them to the fuselage.  I went with one hole in each corner for a total of three; if this proves not enough, it’ll be easy to add two more holes halfway along the sides.  I plan to attach these with blind rivets; easy, and easy enough to remove with a drill if needed later.  Primed the inside surface of the fairings and left to dry.

When testing the pitot heater, I had all three of the annunciator lights lit up on the panel, and grabbed a couple photos.  I really like how these LED indicators worked out, even though they were a bit pricey.  They may end up being too bright at night, but with the way they’re wired, it would be simple to add a bright/dim switch, or even a dimmer pot.  And, they should be dark in the normal condition, so it may be a non-issue.  (The camera makes them look brighter than they actually are, too; the hotspots in the photo aren’t apparent to the naked eye.)  I’m still very happy with the panel design & layout; putting that together was, as expected, one of the highlights of the project.

The bracket comes pre-cut, and pre-bent with a joggle to clear the main spar flange.  I fabricated the reinforcement angle that runs fore-aft along the rib out of a trimmed-off piece of stiffener from some control surface or another (I keep a pile of trimmings, anything large enough to reasonably have a chance of use elsewhere for a bracket or whatever).  Cleco clamps hold everything in place and square for drilling, then I drilled the bracket to the spar.  Adjusted the plate to sit even with the rib by using a piece of aluminum sheet to align them, then clamped that in place and drilled the angle to the rib.  On the bench, I marked and drilled the skin-to-bracket hole pattern, and drilled the angle to the bracket.

Clecoed the drilled bracket to the backside of the wing skin using the main spar rivet holes, and back-drilled the holes in the skin, then cut and filed the center mast hole to size, using the mast itself to test fit.  Disassemble and deburr everything, then dimple the holes as appropriate.  I’ll prime these parts along with the flaps, then rivet the bracketry to the rib; the rest will get riveted along with the bottom skin.

Once both lenses were in place (which completes the LE lights, save for the bulbs) , I flipped the right wing off the stand and into the wing cart, and took apart the stand.  Clecoed the right wing flap & aileron brackets in place, pulled out the aileron/flap gap fairings, and looked at how the flap bracket angles need to be fabricated.  Spent awhile cleaning up the shop from all the projects that have been going on lately…starting to look decent in here again–who knows, might be able get a car or two in here soon!

Trimmed the lens to size with utility knife and bench sander, smoothed with #600 sandpaper, then fit into place using a packing-tape “strap” as described in the instructions.  Drilled, drilled some more, deburred and countersunk, then put together the reinforcing strips that hold the nutplates (prepped these for the right wing install too).  The lens won’t get fit for good until after the next priming session, so that those strips can be primed, but I did install the internal mounting bracket, now that the LE riveting and AOA installs are complete.  Left the bulb out to save it from potential vibration.  I think it ended up looking pretty good.  At some point after it’s flying, I may pursue the “Pete Howell DIY HID modification” to get more light output…but for now, these ought to get the job done.  My plan is to have these on a wig-wag circuit for recognition, as well as taxi/landing steady-on states.

Of course, nothing is ever as easy as it seems; the port fittings install with two countersunk screws, which can fit into a #30 dimple (though they’re not actually #30 screws, it seems).  Drilling them was easy (remove the brass barb from the lower port fitting, and use it as a guide to mark the hole locations).  However, having already installed the leading edge to the wing, dimpling those holes was proved interesting.  There is no way to get a squeezer in there, as the end rib is in the way, plus the ports are 4.75 and 7.5 inches inboard from the skin edge.  I experimented with various tools, assemblies of tools, and different ideas without success.  I finally decided to do what is done on the rear spar: dimple, then “ream out” the dimple.  I dimpled to #40 with the pop-rivet dimplers, then used a #30 countersink in a microstop cage, going one step at a time deeper until the screws sat just flush with the skin.  Having already dimpled the skin prevented the countersink from having to remove too much material.

It may not be the perfect way to install these, but they’re in, and it’s what I had available.  Word to the wise: figure out these locations when you have the assembly clecoed together for the first time, and dimple them with a C-frame type tool!  Either that, or buy the #30 pop-rivet dimplers that I now see are available.  I don’t know if these will be needed elsewhere on the plane, but I may toss in a set with my next order of something, just to have around in case.  It’s a solution in need of a problem just like the one I had tonight.

After all that, I even found time to tidy up the shop and put away the various tools that have been laying around.

Also riveted the LE light brackets together and fit the reflectors in place.  These won’t go into place until the LE assemblies are riveted onto the spar, to save them from vibration.  I’ll fit the lenses once the LE’s are riveted together, but probably off the spar for easier access.